| Martin Tools- Dolly Blocks |
| Type |
Description |
Price |
Shipping |
Light Weight
Toe Dolly
Part #M 1057 |
Designed for flat surfaces. All the features of a
toe dolly.
Sizes 4 3.4" x 2 1/4" x 11/16". Weight 1.8 lbs. |
$36.70 |
$7.16 |
Toe
Dolly
Part #M 1058 |
Thinness and length provide easy accessibility
to narrow pockets. Large, flat face is frequently
used in shrinking and dinging flat panels. The
flat sides furnish a convenient anvil for repairing
flanges. Sizes 4 3/4" x 2 3/8" x 1 1/8". Weight 3.0 lbs. |
$36.70
|
$7.85 |
Shrinking
Dolly
(Serrated)
Part #M 1058S |
Shaped like a toe dolly but has one face
covered with raised serrations for shrinking
metal stretched by dents. Weight 3.4 lbs. |
$35.80
|
$7.85 |
Heel
Dolly
Part #M 1059 |
Design makes it possible to reach easily into
sharp corners and wide radii. These features are
exclusive to the Heel Dolly and continue its high
demand.
Sizes 3 1/4" x 2 1/2" x 1 7/16". Weight 2.7 lbs. |
$32.15
|
$7.85 |
General
Purpose
Dolly
Part #M 1060 |
Provides convenient and comfortable hand
hold during heaviest blows. Weight, balance
and several differently crowned working faces.
Together with two beading and flange lips, give
this dolly broad general use. |
$39.20
|
$7.85 |
Utility
Dolly
Part #M 1061 |
High-crown dolly with one narrow beading edge.
Thick rounded sides are useful in short radii
curves. wide application of uses in high-crown
portions of hoods, fenders and body panels.
Sizes 3 1/8" x 3" x 1 5/8". Weight 2.9 lbs. |
$35.25
|
$7.85 |
Light
Weight
Wedge
Dolly
Part #M 1065 |
Short, slender general purpose dolly. Good hand
grip. Also used for beads or flanges on fenders,
thin edge is useful for corners and beading. Flat
side works under long curve of fender. Sizes 2 7/64" x 2 1/2" x 4 27/64". Weight 2.7 lbs. |
$26.70
|
$7.85 |
Wedge
Dolly
Part #M 1067 |
Long, slender general purpose dolly. Widely
favored by many body repair men for all-around
use. The long, Thin Lip is very useful in working
behind reinforcements.
Sizes 5 3/4" x 2 3/8" x 2 3/16". Weight 4 lbs. |
$39.40
|
$8.17 |
"Champion"
Heavyweight
Dolly
Part #M 1070 |
Heavy duty, general purpose fender dolly. A
necessity on heavy gauge fenders which resist
the blows of lighter dollies. Brings out the
toughest damage. Seats comfortably in the
hand and protects fingers from a swinging blow. Sizes 3 3/8" x 3 3/8" x 2 11/16". Weight 4.6 lbs. |
$35.00
|
$8.41 |
| Martin Tools -Body Spoons |
| Type |
Description |
Price |
Shipping |
Light
Dinging
Spoon
Part #M 1036 |
To ding ridges smooth and level. When
held against ridge and struck with hammer,
spreads blow over large area making
smooth job and preventing damage to metal
or finish. Not made for prying. Length 10"
overall. Face 2" x 4 5/16". Weight .50 lbs. |
$19.95 |
$7.16 |
Combination
Spoon
Part #M 1050 |
General purpose fender spoon. Used as dolly
behind brackets, inner panels and similar
places. Handle offset to give balance when
dinging and for long reach. Has high-crown
working surface. Face 1 3/4" x 5 1/2". Handle 1"
octagon 4 3/4" long. Weight 3.0 lbs. |
$36.10 |
$7.85 |
Spoon
Dolly
Part #M 1052 |
Long handle permits many uses in places
otherwise inaccessible. Can be driven
between reinforcements and outer panel,
then used to pry outward as the metal is
dinged. Excellent forming and caulking tool
for deep pockets of doors, quarter-
panels, rear fenders and lower trunk panels.
Size 2 1/2" x 1" x 3". Weight 4.2 lbs. |
$36.75 |
$8.17 |
Long
Curved
Spoon
Part #M 1054 |
Long, thin, curved blade is handy for prying
up dents behind curved reinforcements
in header panels, hinge anchors in doors,
body pillars and reinforcements in hoods
and radiator shells. Length 10 1/2" overall.
Face 2" x 7". Weight 1.5 lbs. |
$26.90 |
$7.54 |
Heavy Duty
Driving and Fender
Bending
Tool
Part #M 1091 |
Useful for restoration of turned under,
non-wired flanged edges. Also handy for
alignment of inner construction and flanges
on alligator hoods. Heavy formed striking
pads. Length 14 1/8". Weight 3.2 lbs. |
$57.80 |
$8.17 |
Surfacing
Spoon
Part #M 1024 |
Excellent spoon for fender spring
hammering, finishing and shaping. Curve
gets behind inner construction between
panels that are close for removal of
dents. Molds panels. Blade fully polished.
9" Blade Length. 2 1/8" Width.
Overall Length 15 1/8". Weight 2.5 lbs. |
$27.30 |
$7.85 |
Medium
Crown
Spoon
Part #M 1026 |
Long slender shape just like the 1024 surfacing
spoon. Inside with medium crown, for high
ridges or prying. For slapping and surface finishing on fenders, panels and trunk lids.
Blade fully polished. 9" Blade Length. 2 1/8"
Width. Overall Length 14 7/8". Weight 2.5 lbs. |
$27.40 |
$7.85 |
Heavy Duty Double End
S-Spoon
Part #M1044 |
General purpose fender and frame spoon.
Designed to provide further reach on panels
and behind reinforcements. Prying, heavy
duty designed for use on SUV frames. 12 3/16"
Length. 1 3/8" x 2 1/4" face. Weight 2.1 lbs. |
$50.70 |
$7.85 |
